Pay in installments of $5.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 3 - Jul 8
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
palm tree live plant Pachypodium 'lamerei' (Madagascar Palm)Description Light Soil Water Hardiness The Madagascar Palm (Pachypodium lamerei) is a highly distinctive succulent plant known for its striking, palm like appearance. Despite its common name, it is not a true palm but belongs to the Dogbane family (Apocynaceae). It is a pachycaul (thick trunked) stem succulent, meaning its swollen, spiny trunk serves as its main water storage organ. This exotic plant is native to the dry xerophytic forests of southern
-
The Madagascar Palm (Pachypodium lamerei) is a highly distinctive succulent plant known for its striking, palm-like appearance. Despite its common name, it is not a true palm but belongs to the Dogbane family (Apocynaceae). It is a pachycaul (thick-trunked) stem succulent, meaning its swollen, spiny trunk serves as its main water storage organ.
This exotic plant is native to the dry xerophytic forests of southern and southwestern Madagascar, an island off the southeast coast of Africa.
Its most notable feature is its tall, silvery-gray, thick trunk that is densely covered with sharp, triple-grouped spines. This cigar-shaped, succulent stem is topped with a rosette of long, narrow, glossy green leaves, giving it a unique, tropical palm-tree silhouette. The plant may shed its leaves in winter or during prolonged dry periods (semi-deciduous).
-
Full Sun. This plant craves sunlight. Provide at least 6 hours of direct sun daily.
Low Water Needs. Water deeply when the soil is completely dry during the active growing season (spring and summer). Reduce watering significantly, or withhold it entirely, during its winter dormancy, especially if the leaves drop. Overwatering is the biggest threat.
Very Well-Draining Succulent Mix.
Prefers warm temperatures between 65°F and 85°F (18°C - 29°C). It is not frost-hardy and should be protected from temperatures below 40°F (4°C), which can cause cold damage and leaf drop.
-
USDA Zone 9-11
USDA Zone 9b: to -3.8 °C (25 °F)
USDA Zone 10a: to -1.1 °C (30 °F)
USDA Zone 10b: to 1.7 °C (35 °F)
USDA Zone 11: above 4.5 °C (40 °F)
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.8 ★★★★★
Based on 1226 reviews
Sort
Product Reviews
★★★★★ 4
good item
Size: PP67-712 V1
arrived on time , haven't installed as of yet, will add comments once installed but looks like it is what I need and was as described .
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 21, 2019
★★★★★ 5
Direct replacement on my 95 SeaRay 175
Size: PP67-712 V1
My boat started to have issues with not turning over when I used the ignition switch. Replaced the switch and had no effect. Replaced the solenoid and that fixed the problem. Good price, so I replaced all 3 solenoids (Trim/ starter). Solenoids had all needed hardware (nuts/washers)
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 9, 2024
★★★★★ 5
They Fixed My Boat
Size: PP67-712 V1
My boat wouldn’t start, and the outdrive wouldn’t go up or down. So I bought three of these solenoids and replaced the starter and both trim motor solenoids/relays. Now it starts right up with no problems and the trim motor is working again also. I have a 2006 Stingray boat.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 7, 2022
★★★★★ 1
Poor quality
Size: PP67-712 V1
Poor quality. Replaced a starter solenoid on a mercruser 4.3. Right off install it would click but not make a connection to start motor. Confirmed this was the culprit by jumping the terminals. After testing multiple times found it worked a little less than half the time.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 29, 2026
★★★★★ 5
Ya Just Gotta Have One
Size: 7.2 Surround + 3 HDMI
This is a must-have for in-wall wiring of your surround. I chose this one because I installed a 7.2 system with gold-plated jacks and it worked out great. You can get almost any combination of HDMI, subs/surrounds that you need (5.1, 5.2, 7.1, 7.2 etc). Do your planning on location and wire-routing; get good quality speaker wire and HDMI (high-speed with Audio Return Channel); get the remod-style mounting bracket/box then cut your hole at the same height/level as your electrical outlets and preferably between the same studs as your TV's wire-box so your HDMIs just run straight up to the TV (remember to install the bracket BEFORE you run your wires). When connecting the wires to these terminals, it's best to have 10 to 12 inches of wire coming out of the wall because you need space for your hands to manipulate the wires and nuts on the terminals. If you have a basement with access to the floor below the mounting location, it's best to drill 4 half-inch holes straight up through the bottom plate of the wall and feed your wires up those holes. Tip: If your TV and Surround Receiver are fully compatible you really only need 1 HDMI port on the wall plate, because you can plug your devices into the receiver and just sent the A/V/data to the TV while the audio is returned over the same HDMI.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 2, 2016